Click To Call(656) 254-3570Click To Get A Free Estimate
Paver driveway leading to a garage, freshly sealed, on a Carrollwood street

Color back on the drive you pull into daily

Driveway Paver Sealing in Carrollwood, FL

Call (656) 254-3570 to schedule a free estimate and get your faded Carrollwood driveway pavers sealed.

  • Brings out deeper paver color
  • Fresh joint sand helps lock pavers in place
  • Gives weeds less room to grow
  • Makes the surface easier to keep clean
  • Free estimate, no obligation

Request a Free Estimate

Free, no obligation.

Step 1 of 2

Where are your pavers?

Please choose one.

Free EstimateNo obligation
Fast ReplyWithin 1 business day, usually much sooner
Typical Local Price$1.25 to $2.50 a sq ft to clean, sand and seal
Call Now(656) 254-3570

Who seals paver driveways in Carrollwood, and how quickly do I hear back?

A local contractor handles driveway paver sealing across Carrollwood, FL, and your request gets an answer inside 1 business day, and usually much faster. The estimate is free and you can say no without a second thought. To begin, call (656) 254-3570.

Most Carrollwood driveways take more daily wear than any other paved surface on the property, and the wear shows first at the wheel paths and the garage apron. Washing, fresh joint sand and a coat of sealer bring back an even color and keep the joints full. A driveway that is easy to rinse stays that way longer. To have yours looked at, get a free estimate.

Call (656) 254-3570

Pricing

What does it cost to seal a paver driveway in Carrollwood?

What is the published range per square foot?

The range posted around Tampa Bay is $1.25 to $2.50 a square foot for washing, sanding and sealing. Rusty's Pro Wash & Seal gives $1,250 to $2,500 as its example for a typical 1,000 square foot driveway. For a figure built on your own drive, get a free estimate.

What raises or lowers a driveway quote?

Rusty's says big jobs can come closer to $1.00 per square foot, and projects of 3,000 square feet or more using volume pricing may run about $1.00 to $2.00. Small jobs are often set by a minimum charge of $500 to $1,000. Stripping failed old sealer, repairs and leveling push a price up. To find where your drive lands, call (656) 254-3570.

How do I compare two driveway bids?

Compare what each one lists, not only the total. A low figure that skips the joint sand is not the same job, and a high one may fold in repairs the other left out. Already holding a quote? Call (656) 254-3570 and read it against the table below, or review the contractor standards page for questions to ask.

Driveway sizeTypical exampleFull clean, sand and seal
500 sq ftSingle car drive with a walkway$625 to $1,250, the figure in Rusty's calculator for this size
750 sq ftTwo car drive$938 to $1,875, the figure in Rusty's calculator for this size
1,000 sq ftLong two car drive with an apron$1,250 to $2,500, the figure Rusty's gives for a typical driveway
1,500 sq ftWide drive with a turnaround$1,875 to $3,750, the figure in Rusty's calculator for this size

Rusty's Pro Wash & Seal, a Pinellas County company, publishes these sizes for Tampa Bay. Your contractor sets the actual price after seeing the surface, and old sealer, repairs and leveling are usually extra.

Get a Free Estimate

Which neighborhoods near Carrollwood can ask for a driveway estimate?

Homes in Carrollwood and in each place listed below can request a driveway visit, and every place has its own page. Is your street absent from the list? A short call to (656) 254-3570 will settle it.

Contractors applying sealer along a paver driveway with a sprayer and a dry roller
Why choose us

Why do paver driveways fade and stain faster than patios?

A driveway holds more weight, more heat and more oil than any patio, and it has no roof. Four causes show up again and again around Carrollwood, and each is cheaper to handle early. To find out which ones affect your drive, call (656) 254-3570.

Tires and drips

Wheel paths collect oil and rubber, and the sealer under them wears first.

Open sun

Rusty's says driveways in full Florida sun may need a fresh coat near the 3 year mark.

Sprinkler strips

A head that sprays one band of pavers wears that band years before the rest, and Rusty's says hard water minerals leave deposits.

Shade and leaves

Carrollwood Village Park alone holds more than 300 trees, and tree cover over a drive means damp pavers and growth.

Do older Carrollwood driveways need anything extra?

How old is a typical Carrollwood driveway?

Carrollwood was founded in 1959 and built out in the 1960s, with more than 900 homes going up near Lake Carroll between 1959 and 1970, and building spread west in the 1970s and 1980s. A drive laid decades ago may have been patched, widened or sealed more than once. Tell the contractor what you know about its history when you get a free estimate.

What gets checked on an older drive?

Unilock says to test whether old and new sealers are compatible before resealing, and that sealing does not repair drainage or a weak subbase. Pavers that rock near the garage should be reset first. To raise either point, call (656) 254-3570.

How long should the cars stay off a freshly sealed driveway?

When can vehicles go back on?

Rusty's says most driveways need 48 to 72 hours before vehicles return, and about 24 hours before feet. Unilock asks for up to 48 hours of dry weather for the cure, plus clear skies for a day or two before the job. Ask the contractor for the exact window for the product when you call (656) 254-3570.

Where do the cars go in the meantime?

Park on the street or with a neighbor for the stretch, and move anything stored in the garage that you will need. Carrollwood summers bring afternoon thunderstorms most days, and November is usually the driest month around Tampa Bay, so the dry spell has to be chosen with care. Ask what a rained-out day does to the schedule when you get a free estimate.

Will my sprinklers leave stripes on a sealed driveway?

Why do sprinklers mark pavers?

Rusty's says a sprinkler that hits the same strip of a driveway over and over causes wear years earlier than the rest of the surface, and that hard water in parts of Hillsborough leaves mineral deposits that build faster on unsealed pavers. A head that sprays the pavers is worth moving or aiming. To raise it, call (656) 254-3570.

What happens to the timer on sealing day?

Unilock says water can leave white marks on fresh sealer or get trapped under it, so the timer should be off during the cure. Ask the contractor how the heads will be handled when you get a free estimate.

Should my driveway have a wet look or a natural finish?

What does a wet look do on a drive?

Wet look deepens the color and is the finish Rusty's says people request most around Tampa Bay. It shows tire and wheel paths in a darker, richer tone. To see a sample on your pavers, call (656) 254-3570.

When is a natural or matte finish the better pick?

A natural look stays close to the bare paver and suits quieter styles, and Unilock says a penetrating matte keeps more traction than high gloss. A sloped apron that stays wet after rain is the place to think about grip. Tell the contractor about your slope when you get a free estimate.

How often does a paver driveway need resealing?

How many years between coats?

Rusty's puts driveways at every 3 to 4 years, the shortest span of any paved area, and says a drive in full sun may need attention near the 3 year mark. Unilock gives 3 to 5 years for pavers overall. For a check on your own drive, get a free estimate.

What shortens a coat on a driveway?

Tires, oil and open sun wear it down, and tree cover that keeps the pavers damp adds growth to deal with. A wash between coats can help, and the paver cleaning page explains what that visit involves. To plan the calendar, call (656) 254-3570.

Fresh polymeric sand swept into driveway paver joints after a wash

What has to happen before sealer goes on my driveway?

Does the driveway have to be dry?

Yes. Unilock says pavers in a warm, sunny spot may be dry enough to seal a few hours after washing, and pavers in cool shade need about 24 hours. Anything left on the surface, from sand to damp patches, ends up trapped under the coat. To hear how your drive will be timed, call (656) 254-3570.

What happens to the joint sand and the weeds first?

Weeds come out, washed-out sand is replaced, and polymeric sand is swept in so none stays on the faces, then it sets for 24 hours. Unilock adds that water-based sealers can harden joint sand, which helps it resist washout. Ask how your joints will be handled when you get a free estimate.

What if rain or heat is in the forecast on sealing day?

How much clear weather does a sealer need?

Unilock asks for clear skies for 24 to 48 hours before the job, no rain for at least 24 hours after it, and low humidity, with air between 50 and 90 degrees and 75 best. Summer humidity around Tampa Bay makes that window narrower. Ask who decides to move the date when you call (656) 254-3570.

Can hot pavers be sealed?

They should not be. Unilock says applying sealer to overly hot pavers risks staining and early peeling, and summer highs around Tampa Bay average about 91 F. Early starts and shaded stretches help. To plan around the heat, get a free estimate.

Can the walkway and front steps be sealed along with the driveway?

Do the walkway and steps wear on the same schedule?

Not quite. Rusty's puts walkways at every 4 to 5 years, against 3 to 4 for driveways, so the front walk often holds its coat a little longer. Doing both on one visit saves a second trip. To ask about bundling, call (656) 254-3570.

How do the step edges get sealed?

Unilock says a foam roller handles vertical edges and borders, and a metal sheet held along structures stops overspray, since sealer cannot be washed off. Ask who handles the step edges and the garage trim when you get a free estimate.

What if some driveway pavers have shifted or sunk?

Sealer cannot fix them. Unilock says sealing does not cure poor drainage or a weak subbase, and USDA soil data for the Carrollwood Census point lists Zolfo fine sand, which drains somewhat poorly, with a wet zone about 18 inches down from June through November. Low or rocking pavers get reset before any coat, and some quotes list that work as an extra. If a spot near the garage has dropped, mention it when you get a free estimate.

How it works

What process should a driveway sealing quote spell out?

What belongs in writing?

The square footage, the finish, the name of the sealer, the joint sand, the number of coats, any minimum charge and the cure window for cars. A quote that names each one is easy to compare. For one written that way, call (656) 254-3570.

What is the process from first call to parked cars?

The six steps below show the process in order. To start at step one, get a free estimate.

1. A call and a few details

You give your street or ZIP and describe the drive. A local contractor writes or calls back inside a business day, often well inside it.

2. A walk along the pavers

The contractor measures, marks low or rocking pavers, spots old sealer and notes where the sprinklers hit.

3. The written price

You receive the square footage, the finish and what is and is not included, so you can compare bids.

4. Wash, dry and sand

The drive is cleaned in sections, left to dry, and the joints are refilled with polymeric sand that sets for 24 hours.

5. Sealing day

Sprayer, dry roller and foam roller for the borders, all in one session, with the garage area planned so you can park elsewhere.

6. Cars back on

Feet after about 24 hours and vehicles after 48 to 72 hours, as the contractor confirms for the product used.

Photos

What do sealed driveways look like around Carrollwood?

Freshly sealed paver driveway on a Carrollwood driveway
Sealed paver pool deck on a Carrollwood driveway
Sealed paver patio behind the home on a Carrollwood driveway
Sealed paver walkway to a front door on a Carrollwood driveway
Close view of freshly sealed pavers on a Carrollwood driveway
Paver area with one cleaned half beside a dirty half on a Carrollwood driveway
Contractor cleaning pavers on a Carrollwood driveway
Contractor sealing or sanding pavers on a Carrollwood driveway
Questions

Frequently Asked Questions

What is the average cost to seal pavers in Florida?

Around Tampa Bay, companies publish $1.25 to $2.50 per square foot to clean, sand and seal, and Rusty's Pro Wash & Seal says big jobs can approach $1.00. Small jobs are often set by a minimum charge. A driveway is rarely small, so the per foot rate usually decides it.

How much should it cost to seal a paver driveway?

Rusty's lists a 1,000 square foot driveway at $1,250 to $2,500. A drive that size fits a long two car apron with a walkway. Measure the paved area with the contractor, because the square footage drives the whole bid.

How much does it cost to seal outdoor pavers?

The published range covers the wash, the joint sand and the coat together. What lifts a price is failed old sealer, repairs and hard-to-reach areas. When two bids differ, ask each contractor which of those steps are in the number.

Is it good to seal pavers in Florida?

For most driveways, yes. Unilock says a coat deepens color, guards against water, dirt, oil and stains and helps hold sand in the joints. Rusty's puts year-round sun and heavy summer rain at the center of why Tampa Bay pavers need it.

Can I seal my pavers myself?

A homeowner can buy sealer, but a driveway is a large area where a mistake shows for years. Unilock says the whole area should be sealed in one session to avoid gloss differences and that a whitish film can follow over-application. Those are hard to undo.

How long should cars stay off a sealed paver driveway?

Rusty's says most driveways need 48 to 72 hours before vehicles return and about 24 hours for foot traffic. Unilock asks for up to 48 hours of dry weather for the cure. Plan where the cars will sleep before the job day.

Do sprinklers damage a paver driveway in Carrollwood?

They leave marks. Rusty's says a head that hits the same strip over and over wears that strip years sooner and that hard water in parts of Hillsborough leaves mineral deposits. Unilock says to turn sprinklers off during the cure.

My Carrollwood driveway has old sealer on it. Can it be sealed again?

Often, but the old coat matters. Unilock says to test whether the old and new sealers get along before resealing. Failed old sealer may need to come off first, which Rusty's counts as an added cost.

Should my driveway get a wet look or a natural finish?

People ask for wet look more than any other finish around Tampa Bay, Rusty's says, and it deepens color. Unilock says a penetrating matte keeps more traction. A sloped apron that stays wet after rain may do better with the matte.

Is there a minimum charge for a short driveway?

Often there is. Rusty's says small projects are commonly set by a minimum charge of $500 to $1,000. A short single car drive may fall into that minimum rather than the per foot rate.

Can the walkway be sealed on the same visit as the driveway?

Usually yes. Rusty's puts walkways at every 4 to 5 years and driveways at 3 to 4, so the two can be done together even though the walk may not need it as soon. Ask for the walkway as its own line in the quote.

What should a driveway sealing quote include?

The area in square feet, the sealer by name, the finish, the joint sand, the number of coats, any minimum charge and how long cars stay off. Those are the points that make two bids comparable.

Want the driveway looking even again?

Phone or send the short form, and a local contractor writes back within 1 business day, often within hours.

Call (656) 254-3570

Free, no obligation